- Verarbeitung von 4 Industrie-Normsignalen einzeln konfigurierbar als Strom- oder Spannungssignal
- 4 galvanisch getrennte I/O Kanäle Schutz vor Messfehlern durch Erdungsprobleme und Störspannungsverschleppung
- Sichere 5-Port-Trennung bis 300 V AC/DC, Prüfspannung 3 kV
- Schnelle Signalerfassung hohe Messrate, kurze Verarbeitungszeit
- In-Rail-Bus Konnektor für Modbus und Versorgung, erlaubt eine schnelle und kostengünstige Installation
- Frei skalierbar bis zu 247 DRAGO Module in einem Modbus-Segment
- Extrem schmale Bauform 6,2 mm schmales Anreihgehäuse für eine einfache und platzsparende Hutschienen-Montage
- Made in Germany 5 Jahre Garantie
 Datasheet |
| User Manual |
| Modbus Manual |
- Acquisition of 4 industrial standard signals individually configurable as current or voltage input
- 4 galvanic isolated inputs protection against erroneous measurements due to parasitic voltages or ground loops
- Protective 5 port separation up to 300 V AC/DC, Test voltage 3 kV
- Fast signal acquisition high measuring rate, short processing times
- In-Rail-Bus connector for Modbus and Power Supply allows fast and economical installation
- Freely scalable up to 247 DRAGO Module in one Modbus segment
- Extremely slim design 6.2 mm slim housing for a simple and space saving, DIN rail mounting
- 5 Years Warranty Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)
| Datasheet |
| User Manual |
| Modbus Manual |
- 4 channels independent controllable digital I/Os
- Each channel programmable as input or output
- Programmable switch-ON and switch-OFF behavior
- Extensive programmable operating functions Frequency or counter input, frequency, puls or PWM outputs
- Protective 5-way separation up to 300 V AC/DC, test voltage 3 kV
- Status indication for each channel
- In-Rail-Bus Connector for Modbus and power supply
- Extremely slim only 6.2 mm installation width
- Made in Germany 5 Years Warranty
| Datasheet |
| User manual |
| Modbus Manual |
- 4 channels 4 independent power relays
- Programmable switch-ON and switch-OFF behavior
- Extensive programmable operating functions such as limit value monitoring
- Protective 5-way separation up to 300 V AC/DC, test voltage 3 kV
- Status indication for each relay
- In-Rail-Bus Connector for Modbus and power supply
- Extremely slim only 6.2 mm installation width
- Made in Germany 5 Years Warranty
| Datasheet |
| User Manual |
| Modbus Manual |
The Modbus RTU Connection Module is used to connect the 24 V supply and the Modbus lines A and B to the In-Rail-Bus DIN rail connector. The power supply and the Modbus lines are connected to the terminals of the module (screw terminals). The connection to the In-Rail-Bus DIN rail connector is made via the rear spring contacts. All other DRAGO I/O modules are thus pre-wired via the In-Rail Bus with power supply and bus lines. DIP switches can be used to switch the termination and polarization resistors normally used for RS485 interfaces. An additional line is available for group messages, e.g. for a group error message, as far as this is supported by the I/O modules. The Modbus RTU connection module can also be used for feed out, especially if further modules are to be connected in separate installations. Additional terminals for the bus lines are provided for this purpose.
| User Manual |
| Modbus Manual |
- Input for Standard Signals 0-20 mA, 4-20 mA, 0-10 V, 0-5 V
- In-Rail-Bus Connector for Modbus and power supply
- Protective Separation up to 300 V AC/DC, test voltage 3 kV
- Easy configurable via DIP switches or Modbus interface
- Freely scalable up to 247 measuring inputs in one Modbus segment
- Extremely slim only 6.2 mm installation width
- Made in Germany 5 Years Warranty
| Datasheet |
| User Manual |
| Modbus Manual |
- High performance measuring input for all industrial sensors: Pt, Ni, TC, KTY, mA, V, mV, Ω, Pot, Hz, PWM
- Uni-/Bipolar and TRMS capture of current and voltage
- Easy configurable by DIP switch or USB interface
- 15 programmable user-specific settings directly selectable via DIP switches
- Freely scalable up to 247 DRAGO devices in one Modbus segment
- Protective Separation up to 300 V AC/DC, test voltage 3 kV
- Highest accuracy measuring resolution up to 24 bit
- Fast measured value processing high data rate
- In-Rail-Bus Connector for Modbus and power supply
- Extremely slim only 6.2 mm installation width
- Made in Germany 5 Years Warranty
| Datasheet |
| User Manual |
| Modbus Manual |
Systemvoraussetzungen
- PC mit Windows XP, Vista oder Windows 7, 8, 10
- USB-Schnittstelle
- USB-Konverter
