- Force-measuring device combination consisting of an external measurement sensor and a high-resolution display unit
- Ideal for force measurement of very slight forces or loads in machines and plants
- Real time or Peak Hold Mode to observe transcients or capture peaks
- Push & Pull function to capture tensile and compressive forces
- Mini Statistics Kit: calculates the average result from up to ten stored single results, min., max., n
- Function to set limits: Input of an upper/lower limit value. A visual and acoustic signal supports the measuring operation
- Rechargeable battery pack internal, battery charger included
- Depending on the display unit, only one measuring cell can be connected
- Suitable for all SAUTER test stands (When ordering a test stand please state)
- Technical data
- External sensor: Dimensions LxWxH 76x65x22 mm, net weight approx. 0,3 kg (without sensor)
- Cable length for display unit approx. 2 m
- Tolerance 1 % of [Max]
- Selectable measuring units: N, kg, lb
- Overload protection: 150 % of [Max]
- Turnable display with backlight
- Digital force gauge with remote sensor
- Data interface RS-232
- Selectable measuring units: N, lb, kg, kN, t
- Real time or Peak Hold Mode to observe transcients or capture peaks
- Function to set limits, programming of Max./Min., in pull and push direction, with output of audible and optical signal. Ideal mode for efficient and accurate testing of standard parts
- Auto-Power-Off
- Mini Statistics Kit: calculates the average result from up to ten stored single results, min., max., n
- Turnable display with backlight
- Can be mounted on all manual test stands
- Digital force gauge with internal sensor
- Data interface RS-232, included
- Standard attachments: as shown below, extension rod: 90 mm
- Delivered in a hard carrying case
- Selectable measuring units: N, lb, kg
- Real time or Peak Hold Mode to observe transcients or capture peaks
- Function to set limits, programming of Max./Min., in pull and push direction, with output of audible and optical signal. Ideal mode for efficient and accurate testing of standard parts
- Auto-Power-Off
- Mini Statistics Kit: calculates the average result from up to ten stored single results, min., max., n
- Turnable display: automatic direction identification
- Secure operability due to ergonomic design
- Real time or Peak Hold Mode to observe transcients or capture peaks
- Selectable measuring units: N, lb, kg, oz
- Auto-Power-Off
- With one of the two optional attachments for tensile strength testing, the SAUTER FK can become a tensiometer for testing the material tension characteristics of cables, threads, wires, twine etc. (see accessories)
- Standard attachments: as shown below, extension rod: 90 mm
- Can be mounted on all test stands
- Turnable display with backlight
- Real time or Peak Hold Mode to observe transcients or capture peaks
- Metal housing for durable usage in harsh environmental conditions
- Can be mounted on all SAUTER test stands
- Capacity display: A bar lights up to show how much of the measuring range is still available
- Function to set limits, programming of Max./Min., in pull and push direction, with output of audible and optical signal. Ideal mode for efficient and accurate testing of standard parts - ideal mode for efficient and accurate testing of standard parts
- Internal memory for up to 500 measurements
- Continuous analogue output: Linear voltage signal in relation to the load (0–2 V)
- Delivered in a hard carrying case
- Standard attachments: as shown below (not for SAUTER FL 2K)
- Selectable measuring units: N, kN, kgf, ozf, lbf
- PEAK function to fix the current measured values
- Turnable display with backlight
- Selectable measuring units: N, lb, kg, g
- SAUTER FT 50, FT 200 with internal sensor
- KERN FT 1K with remote sensor, see enlarged picture
- Standard attachments: as shown below; extension rod: 125 mm
- Delivered in a hard carrying case
The force sensor HySense® FO 110 is a shear force sensor according the deflecting beam principle. Since a force and the deflection of a beam is proportional, this sensor is able to determine a force by measuring its elongation or change in length. Due to its compact design, these traction-pressure force sensors can be used in the laboratory, as well as in industrial environments. Made with corrosion-proof steel, HySense® FO 110 have a standardized nominal characteristic value. They can be mounted easily allowing simple integration into existing structures. It is available for several measurement ranges from 0-20 kN. Measuring / collection of e.g.
- moulding and insertion forces
- spring forces
- cutting forces
- force and force control during assembly
- pressing forces in drilling machines
The force sensor HySense® FO 210 is a traction force sensor. It works to the principle of centerline force measurement. The force sensor is a threaded rod. This allows easy and universal fastening. The application chamber for the resistance strain gauge is protected from mechanical and chemical damage by an aluminium tube, cast with a highly elastic compound. Full bridges of resistance strain gauges measure the elongation and lateral expansion caused by traction forces. It is available for several measurement ranges from 0-250 kN. Applications / measurement ranges:
-
- Lifts
- Cranes and housings
- Twistings of masts, towers or platforms
