- 4-20mA loop-powered output
- +/- 0.25% accuracy available
- Wide selection of pressure ranges available
- Turndown 6:1 (3:1 Turndown for model SPX 2290)
- Configurations available for use in hazardous locations
- Remotely configurable via HARTTM
- Precise, repeatable pressure measurements
- Output supplied directly to DSC or PLC
- Meets CE requirements
- CE ATEX Intrinsically Safe Approved
- FM Explosion Proof Approved
- CSA Explosion Proof Approved
- SIL 2 Certified (Pressure Output)
- PL'c' Certified (Relay Output)
- Additional approvals are available
 Datasheet
|
- 4-20mA loop-powered output
- +/- 0.15% accuracy available
- Reduced temperature drift by 80% over non compensated units
- Temperature output available (RTD or 4-20mA)
- Wide selection of pressure ranges available
- Turndown 6:1
- Configurations available for use in hazardous locations
- Remotely configurable via HART
- Precise, repeatable pressure measurements
- Output supplied directly to DSC or PLC
- Meets CE requirements
- CE ATEX Intrinsically Safe Approved
- FM Explosion proof approved
- CSA Explosion proof approved
- SIL 2 Certified (pressure output)
- PL'c' Certified (relay output)
- Additional approvals are available
| Datasheet |
- 4-20mA loop-powered output
- +/- 0.25% accuracy available
- Wide selection of pressure ranges available
- Turndown 6:1
- Configurations available for use in hazardous locations
- Remotely configurable via HART
- Precise, repeatable pressure measurements
- Output supplied directly to DSC or PLC
- Meets CE requirements
- CE ATEX Intrinsically Safe Approved
- SIL 2 Certified (pressure output)
- PL'c' Certified (relay output)
- Additional approvals are available
| Datasheet |
- 4-20mA loop-powered output
- Improved accuracy with Dynalarity ±0.2% available
- Wide selection of pressure ranges available
- Turndown 3:1
- Configurations available for use in hazardous locations
- Remotely configurable via HARTTM
- Precise, repeatable pressure measurements
- Output supplied directly to DSC or PLC
- Meets CE requirements
- CE ATEX Intrinsically Safe Approved
- FM Explosion Proof Approved
- CSA Explosion Proof Approved
- SIL 2 Certified (Pressure Output)
- PL'c' Certified (Relay Output)
- Additional approvals are available
| Datasheet |
- Adjustable zero and span, via side-mounted pots
- Accuracy better than ±0.5%
- DyMax® coated stainless steel wetted parts
- 4-20 mA output
- 0-500 to 0-30,000 psi
- Internal 80% shunt calibration
- 3rd-party agency analysis (exida™) and self-certified based on FMEDA analysis and internal audit
- Output signal meets Performance Level ‘c’ as defined by the Machinery Directive (Category 1)
- Meets the following compliance directives, when properly installed and used:
- –SIL2
- Machinery Directive EN ISO 13849-1
| Datasheet |
- Adjustable zero and span
- Accuracy better than +/- 0.5%
- Dymax® coated stainless steel wetted parts
- 0 - 5 Vdc and 1 - 6 Vdc outputs
- 0 - 500 to 0 - 30,000 psi
- Internal 80% shunt calibrations
- Adapt transmitter to process conditions
- Repeatable, reliable pressure measurements
- Superior abrasion resistance
- Direct input to supervisory control systems
- Wide variety of pressure ranges
- Easy to calibrate and use
| Datasheet |
- Adjustable zero and span
- Accuracy better than ±0.5%
- DyMax® coated stainless steel wetted parts
- 0 - 10 Vdc and 1 - 11 Vdc outputs
- 0 - 500 to 0 - 30,000 psi
- Internal 80% shunt calibrations
| Datasheet |
Smart pressure transmitter. FM approved models available. Intrinsically safe models available. Data sheet only available in English.
| Datasheet |
Smart pressure transmitter. FM approved models available. Intrinsically safe models available. Data sheet only available in English.
| Datasheet |
| Datasheet |
The pressure transmitters of the MDT series are based on the proven MDA series. The existing process pressure is converted into a proportional volt output signal by an integrated amplifier in three or two-wire technology. This ensures signal transmission independent of interference, even over longer distances.
| Datasheet |
The pressure transmitters of the MDT series are based on the proven MDA series. The upcoming
| Datasheet |
The new pressure transmitter series MDT was specially developed for problem-free use in critical environments with high interference potentials, whereby the 4-20mA current signal can be transmitted over long distances without interference, even with connecting cables without a screen.
| Datasheet |
The new pressure transmitter series MDT was specially developed for problem-free use in critical environments with high interference potentials, whereby the 4-20mA current signal can be transmitted over long distances without interference, even with connecting cables without a screen. These versions have a special, short pressure sensor head with a mounting nut ½-20 UNF thread and a flexible, partially free capillary to the amplifier housing. They are therefore particularly suitable for use in confined spaces.
| Datasheet |
- HART digital communication
- Better than +/- 0.25% combined error
- 4 - 20 mA loop-powered output
- 0 - 250 to 0 -30,000 psi
- Explosion Proof, Intrinsically Safe/ATEX approved*
- Meets PED and CE requirements
- Configurable via handheld
- Precise repeatable pressure measurments
- Output supplied directly to DCS or PLC
- Customer defined pressure ranges
- Approved for hazardous environments
- Meets new EC requirements
| Datasheet |
- Simple and inexpensive 2-wire connection, unshielded in the toughest interference field environment
- ATEX approval: II 2 G EEx ia IIC T4
- Meets NAMUR regulations NE21 and NE43
- Smart transmitter with HARTTM communication
- Series with 0.25% and 0.5% accuracy
- Pressure measuring ranges 0-70 to 0 - 2000 bar
- Process temperature up to 400°C
- Autozero and Autocal
| Datasheet |
- Simple and inexpensive 2-wire connection, unshielded in the toughest interference field environment
- ATEX approval: II 2 G EEx ia IIC T4
- Meets NAMUR regulations NE21 and NE43
- Smart transmitter with HARTTM communication
- 0.5% accuracy
- Pressure measuring ranges 0-100 to 0 - 2000 bar
- Process temperature up to 400°C
- Autozero and Autocal
| Datasheet |
- 1/2-20 UNF thread pressure transmitter
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.25% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- Small diaphragm and mounting flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.25% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- Large diaphragm and optional split flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.25% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- Meets CE-PED requirements for European standards
- 0-500 to 0-10,000psi range options
| Datasheet |
- Large diaphragm and mounting flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.25% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- 1/2-20 UNF thread pressure transmitter
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.15% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- Small diaphragm and mounting flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.15% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- Large diaphragm and optional split flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.15% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
- Large diaphragm and mounting flange for easier installation
- Reduce temperature drift by ~80% over non-compensated units
- Accuracy to ±0.15% FS
- Temperature output available (RTD or 4-20mA)
- HART™ digital communications
- 0-500 to 0-10,000psi range options
- Rugged welded electronics housing
| Datasheet |
The pressure transmitters of the TDT series are based on the proven TDA series. The existing process pressure is converted into a proportional volt output signal by an integrated amplifier in three or two-wire technology. This ensures signal transmission independent of interference, even over longer distances. Thanks to the integrated thermocouple, it is possible to measure the temperature directly on the medium at the same time.
| Datasheet |
The new pressure transmitter series TDT was specially developed for problem-free use in critical environments with high interference potentials, whereby the 4-20mA current signal can be transmitted over long distances without interference even with connecting cables without a screen.
| Datasheet |
