• MultiSafe DSP-HW 2 voltage warner for flooded cellars and maintenance shafts
• cable reel with 30 m connecting cable
• handle with ball electrode for probing and for dipping into the water
• nominal voltage range: 12 – 1000 V AC / 12 – 1500 V DC
• integrated self-test
• included accessories: screw clamp HW-SZ for earthing on masts earthing spike HW-SPI400 400 mm artificial leather bag DSP-HW 2-BAG

Datasheet

User Manual

Since 1948, DUSPOL^® voltage testers are used in the electrical trade and industry. Today, frequency-controlled voltages and high system voltages in photovoltaic systems and wind power plants, in electric vehicles and industrial applications have become the benchmark for voltage testers. Particularly for the DUSPOL^® digital, the following applies:

• VDE-tested and approved in compliance with EN 61243-3
• measuring category CAT IV 600 V, CAT III 1000 V
• voltage testing from 1.0 V to 1000 V AC TRUE RMS / 1200 V DC
• frequency and resistance measurement, diode test
• functions of the DUSPOL^® expert

Scope of delivery incl. batteries

Datenblatt

BENNING excels by many years of experience in the development of two-pole voltage testers and high quality. DUSPOL^® can be used in modern applications and meets the high safety standards in industry and trade.

• VDE-tested and approved in compliance with EN 61243-3
• safe voltage testing for voltages of up to 1000 V AC/DC, from 50 V even in case of empty batteries
• measuring category CAT IV 600 V, CAT III 1000 V
• acoustic / visual continuity test
• LED measuring point illumination
• non-contact cable break detector
• functions of the DUSPOL^® analog

Scope of delivery incl. batteries

Datenblatt

For more than 70 years, BENNING has been developing two-pole voltage testers at the highest level. The DUSPOL^® voltage tester is professionally used worldwide in industry and trade, e. g. in electrical installations, on machines and systems related to renewable energy.

• VDE-tested and approved in compliance with EN 61243-3
• safe voltage testing for voltages of up to 1000 V AC/DC
• measuring category CAT IV 600 V, CAT III 1000 V
• load connection with vibration alert
• intentional tripping of a 30 mA RCD
• phase sequence test in a three-phase mains
• single-pole phase test
• no batteries required

Datenblatt

The MultiSafe DSP 4 is a safe, easy-to-use testing tool for all sectors of industry and power engineering. A versatile, robust and completely safe voltage tester with multimeter precision. Protective resistors directly behind both test electrodes offer maximum safety against surge voltage. The MultiSafe turns itself on / off automatically.

Datasheet

User manual

The MultiSafe DSP 5 is the safe, easy-to-use testing tool for all sectors of industry and power engineering. It combines highest safety CAT IV – 1000 V, easy operation and multimeter precision in a voltage tester. The voltage tester meets all the requirements of a modern, safe test equipment and is equipped with its wide range of functions for future tasks. The MultiSafe turns itself on / off automatically.

User manual

Compact voltage tester with easy operation and without battery. All test functions are maintenance-free. Voltage display by LCD and LED with continuity, phase and phase sequence tester. The ProfiSafe LSP 4 is a particularly safe and handy voltage tester that facilitates daily work thanks to its clear display and very easy operation. It is the optimal testing tool for craft and industry.

Datasheet

User manual

The test ball ZAP 350 is the ideal testing tool for energy suppliers. It combines a robust voltage tester with a safe test tool for a quick start-up test when commissioning electricity meters. The additional 350 W load is securely and waterproof integrated into our patented connection line. Thus, tests can be carried out safely in any environment.

Datasheet

User manual

The Prüfball ZAP Digital is a safe tool for a quick start-up test when commissioning electricity meters, combined with a high-quality voltage tester. Its ball-like rubber housing encapsulates the measuring electronics and optimally protects against hard impacts, water, dust and electric shock. This makes the Prüfball indestructible, safe and durable.

Datasheet

User manual

User manual

The Prüfball Digital is a maintenance-free voltage and continuity tester for the power supply and industry. Protected by its unique rubber housing, the Prüfball is indestructible, safe and durable. The Ball SPB Digital combines state-of-the-art microcontroller technology with the proven features of the analogue test ball -accurate, robust, maintenance-free.

Datasheet

User manual

Specifications: •   Voltage: 3 mVDC to 1,000 VDC/ 100 mVAC to 1,000 VAC •   Resistance: 0.3 Ω to 30 MΩ •   Capacitance: 400 pF to 30 mF •   Diode test •   Audible continuity for R ≤ 30 Ω •   600 V CAT III

Datasheet

User Manual

• Automatic recognition of AC/DC
• Automatic recognition of resistors, diodes & capacitors
• Autoranging
• Hazardous voltage indication
• Removable test probes

Datasheet

User manual

Specifications:  

• CAT IV 1,000 V
• IP65
• Full autotest
• Voltage detection, LED display: 12 VAC ≤ U ≤ 1,000 VAC • 12 VDC ≤ U ≤ 1,400 VDC
• Frequency: DC, 16_2/3 to 800 Hz
• Detection of stray voltages
• Unipolar phase detection (a single contact)
• Two-pole phase-sequence testing with 2-wire method = a third hand is not required
• Continuity test with audible and visual indication (R < 100 Ω)
• Extended continuity test with visual indication for R < 2 kΩ , 60 kΩ and 300 kΩ
• RCD trip test
• Complies with EN 61243-3 & IEC 61010 1000 V CAT IV
• Climatic conditions:-30 °C to +60 °C (Class S)
• Battery life > 5,000 x 10 s measurements
• Removable lead and test probe
• Delivered complete and ready to use

Datasheet

User manual

Specifications:

• CAT IV 1,000 V
• IP65
• Full autotest
• Voltage detection, LED display + backlit digital display: 12 VAC ≤ U ≤ 1,000 VAC • 12 VDC ≤ U ≤ 1,400 VDC
• Frequency: DC, 16_2/3 to 800 Hz
• Stray voltage detection
• Unipolar phase detection (a single contact)
• Two-pole phase-sequence testing with 2-wire method = a third hand is not required
• Continuity test with audible and visual indication (R < 100 Ω)
• Extended continuity test with visual indication for R < 0.5 Ω to 2.999 kΩ
• RCD trip test
• Complies with EN 61243-3 & IEC 61010 1000 V CAT IV
• Climatic conditions: -15 °C to +45 °C (Class N)
• Battery life > 2,500 x 10 s measurements
• Removable lead and test probe
• Delivered complete and ready to use

Datasheet

User manual

HT10 is designed to carry out the measurements of a digital tester in a practical, quick and functional way thanks to his narrow and long structure, which allows carrying out measurements in any operating conditions. This device carry out measurements of AC/DC voltage with polarity indication, continuity tests with buzzer and phase sequence detection with LED indications and Display reading. HT10 carry out measurements of AC voltage with low input impedance and performs RCD trip (just trip, no time or current testing) testing as well. It's also provided with a white LED torch for use in poorly lit environments, and comply with safety requirements of standards IEC/EN61243-3:2014/VDE 0682 ensuring safe and reliable working conditions. The instrument indicate whether a dangerous voltage is present, even if there is no battery power supply or a failure of the main circuit. The instruments also comply with IEC/EN61010-1 and IEC/61010-2-030 in CAT IV 600V, CAT III 690V (HT10 CAT IV 600V, CAT III 1000V). Protection class IP64 (dust and splash-proof) and molded soft rubber grips make HT10 heavy duty instruments ideal for the toughest jobs in domestic or industrial applications.

Datasheet

User manual

Pen phase detector HT20 allows very quickly checking for the presence of AC voltage on any kind of electric installation with and without direct contact. A red LED turns on and a buzzer sounding reveal the presence of voltage.

Datasheet

User manual

HT6 is designed to carry out the basic measurements of a digital tester in a practical, quick and functional way thanks to their narrow and long structure, which allows carrying out measurements in any operating conditions. HT6 carries out measurements of AC/DC voltage, Continuity tests with buzzer, Diode test and Phase sequence with LED indication. These devices are provided with a white LED torch for use in poorly lit environments and complies with safety requirements of standards IEC/EN61243-3:2010, IEC/EN61010-1 and IEC/61010-2-030 in CAT IV 600V, CAT III 690V.

Datasheet

User manual

The HT7 voltage tester is built and tested according to EN 61243-3 and ensures safe and reliable working. It complies with protection class IP64 (dust and splash-proof) and is robust due to the molded soft rubber grips, making it ideal for the toughest jobs in the manual or industrial sector. The firmly connected measuring tip guard eliminates the risk of injury when carrying in clothing bags or in the tool bag.

User manual

HT712 is designed to practically and functionally performing the basic functions of a common digital tester in an extremely easy and quick way thanks to its narrow and long structure. Model HT712 also allows performing measurements of Voltage and Frequency and Phase Sequence with the innovative and patented method with 1 terminal also directly on the isolating sheaths of the cables.

Datasheet

User manual

HT8 is designed to carry out the basic measurements of a digital tester in a practical, quick and functional way thanks to their narrow and long structure, which allows carrying out measurements in any operating conditions. Carries out measurements of AC/DC voltage, Continuity tests with buzzer, Diode test and Phase sequence with LED indications and Display reading. HT8 is provided with a white LED torch for use in poorly lit environments and complies with safety requirements of standards IEC/EN61243-3:2010, IEC/EN61010-1 and IEC/61010-2-030 in CAT IV 600V, CAT III 690V.

Datasheet

User manual