- Measuring ranges up to 0 ... 1,000 bar (0 ... 15,000 psi), vacuum and absolute pressure ranges also available
- Accuracy: up to 0.05 % (incl. calibration certificate)
- Intrinsically safe version
- Logger function with up to 50 measured values per second
- Communication with WIKA-CAL software over WIKA-Wireless
 Datasheet |
| User Manual |
- Measuring ranges from -1 … +16 bar to 0 … 1,000 bar (-14.5 ... 230 psi to 0 ... 14,500 psi)
- Accuracy: 0.25 % (incl. calibration certificate)
- Robust case with protective rubber cap
- Simple operation using four buttons
- Complete service cases incl. pressure generation available
| Datasheet |
| User Manual |
- Druckbereich von 0 …100 mbar bis 0 ... 400 bar
- Datenlogger
- grafikfähiges Display
- Edelstahlgehäuse Ø 100 mm
- USB 2.0 Schnittstelle
- Optional
- Kalibrierzertifikat nach DKD / DAkkS
- Ex-Ausführung Zone 1
- Software inkl. USB-Konverter
- Funktionen
- Nullpunkt-Justage
- Datenlogger
- Abschaltautomatik
- freie Tastenbelegung
- Hintergrundbeleuchtung u. v. m.
|
Datasheet
|
- Druckbereich von 0 ... 600 bar bis 0 ... 2200 bar
- Datenlogger
- grafikfähiges Display
- Edelstahlgehäuse Ø 100 mm
- USB 2.0 Schnittstelle
- Optional
- Kalibrierzertifikat nach DKD / DAkkS
- Ex-Ausführung Zone 1
- Software inkl. USB-Konverter
- Funktionen
- Nullpunkt-Justage
- Datenlogger
- Abschaltautomatik
- freie Tastenbelegung
- Hintergrundbeleuchtung u. v. m.
|
Datasheet
|
IDM-60A is a digital manometer with an analogue output signal 4-20 mA. Again, the IDM-60R is a digital manometer with an output signal Rs485 bus system.
|
User Manual
|
|
User Manual
|
|
User Manual
|
- Digital contact gauge
- 3-digit 14 mm LED display
- 63 mm stainless steel case
- Min./max. memory
- Ranges from 250 mbar to 250 bar
- Dry ceramic sensor
- Analog output: 0(4)...20 mA, 0...10 V
- Contact output: DC PNP, max. 200 mA
|
Datasheet
|
|
User Manual
|
|
Datasheet
|
- 4 digit LED display
- 2 relays 250V AC / 125V DC
- Recording min./max. pressure
- Dry capacitive ceramic sensor
- Smallest measuring range: 0…25 mbar
- Largest measuring range: 0…250 bar
- Negative measuring range: up to -1 bar
- Accuracy ≤ 0,2%
- Analog output: 4…20 mA, 2-wires 0…10 V, 3-wires 0...20 mA, 2-wires
| Datasheet |
| User Manual |
- Dry ceramic sensor
- Ranges from 25 mbar to 60 bar
- Global errror < 0,2% F.S.
- High overload capability
- 2 adjustable switch settings
- Analog output 0(4)...20 mA or 0...10 V
|
Datasheet
|
- Dry ceramic sensor
- Ranges from 25 mbar to 60 bar
- Global errror < 0,2% F.S.
- High overload capability
- 2 adjustable switch settings
- Analog output 0(4)...20 mA or 0...10 V
| Datasheet |
- Nominal pressure:
- from 0 ... 100 mbar
- up to 0 ... 600 bar
- rotatable housing
- 2-line LC display
- 4.5-digit 7-segment display
- 6-digit 14-segment additional display
- min / max function with reset function
- offset and end point calibration
- setting the pressure unit (bar, mbar, psi, InHg, cmHg, mmHg,hPa, kPa, MPa, mH2O)
- switch-off automatic
|
Datasheet
|
|
User Manual
|
- Nominal pressure:
- from 0 ... 100 mbar
- up to 0 ... 600 bar
- rotatable housing
- 2-line LC display
- 4.5-digit 7-segment display
- 6-digit 14-segment additional display
- min / max function with reset function
- offset and end point calibration
- setting the pressure unit (bar, mbar, psi, InHg, cmHg, mmHg,hPa, kPa, MPa, mH2O)
- switch-off automatic
|
Datasheet
|
|
User Manual
|
- Nominal pressure
- from 0 ... 400 mbar
- up to 0 ... 600 bar
- rotatable housing
- 2-line LC display
- 4.5-digit 7-segment display
- 6-digit 14-segment additional display
- different mechanical connections: inch, NPT threads
- min / max function with reset function
- offset and end point calibration
- setting the pressure unit (bar, mbar, psi, InHg, cmHg, mmHg,hPa, kPa, MPa, mH2O)
- switch-off automatic configuration
|
Datasheet
|
|
User Manual
|
- Nominal pressure:
- from 0 ... 400 mbar
- up to 0 ... 600 bar
- rotatable housing
- 2-line LC display
- 4.5-digit 7-segment display
- 6-digit 14-segment additional display
- different mechanical connections: inch, NPT threads
- min / max function with reset function
- offset and end point calibration
- setting the pressure unit (bar, mbar, psi, InHg, cmHg, mmHg, hPa, kPa, MPa, mH2O)
- switch-off automatic configuration
|
Datasheet
|
|
User Manual
|
The high precision of the LEX1 digital manometers makes them ideally suited to calibration and test applications. The minimum or maximum value since the last reset can be displayed at the same time as the current pressure value in a wide variety of units of pressure. Power is supplied by a conventional CR2430 coin cell battery (provided).
|
Datasheet
|
|
User Manual
|
- Rugged, waterproof stainless steel housing with safety glass face
- Large, easy-to-read 5-digit LCD display with 5/8” digits
- Operation by capacitive touch buttons
- Pressure peak with 5 kHz sampling frequency and high resolution measurment in standard mode
- Rechargeable accumulator power supply
- Record function (pressure, peak pressure, temperature, measurement time)
- USB-interface for configuration, download, and power recharge
|
Datasheet
|
|
User Manual
|
The 2000 Series offers twin input fordifferential or gauge measurement with pressure ranges from 25mbar to 10bar.
|
Datasheet
|
|
User Manual
|
- Measuring ranges up to 0 ... 1,000 bar (0 ... 15,000 psi), vacuum and absolute pressure ranges also available
- Accuracy: up to 0.05 % (incl. calibration certificate)
- Intrinsically safe version
- Logger function with up to 50 measured values per second
- Communication with WIKA-CAL software over WIKA-Wireless
| Datasheet |
| User Manual |
- Druckbereich von 0 …100 mbar bis 0 ... 400 bar
- Datenlogger
- grafikfähiges Display
- Edelstahlgehäuse Ø 100 mm
- USB 2.0 Schnittstelle
- Optional
- Kalibrierzertifikat nach DKD / DAkkS
- Ex-Ausführung Zone 1
- Software inkl. USB-Konverter
- Funktionen
- Nullpunkt-Justage
- Datenlogger
- Abschaltautomatik
- freie Tastenbelegung
- Hintergrundbeleuchtung u. v. m.
|
Datasheet
|
- Druckbereich von 0 ... 600 bar bis 0 ... 2200 bar
- Datenlogger
- grafikfähiges Display
- Edelstahlgehäuse Ø 100 mm
- USB 2.0 Schnittstelle
- Optional
- Kalibrierzertifikat nach DKD / DAkkS
- Ex-Ausführung Zone 1
- Software inkl. USB-Konverter
- Funktionen
- Nullpunkt-Justage
- Datenlogger
- Abschaltautomatik
- freie Tastenbelegung
- Hintergrundbeleuchtung u. v. m.
|
Datasheet
|
Hold, Zero, 7 selectable units, smoothing, lock, Max/Min.IP67
This unit features a 0 - 25 millibar operating range and a 350 millibar over range. It is also IP67 rated.
|
Datasheet
|
|
User Manual
|
Hold, Zero, 7 selectable units, smoothing, lock, Max/Min.IP67 This unit features a 0 - 130 millibar operating range and a 750 millibar over range. It is also IP67 rated.
|
Datasheet
|
|
User Manual
|
Hold, Zero, selectable units, smoothing, lock, Max/Min.IP67 Featuring 0-2 bar absolute operating range and a 4 bar over range. This product is also IP67 rated.
|
Datasheet
|
|
User Manual
|
Hold, Zero, 7 selectable units, smoothing, lock, Max/Min.IP67
This unit features a 0-2 bar operating range and a 4 bar over range. It is also IP67 rated.
|
Datasheet
|
|
User Manual
|
Hold, Zero, 7 selectable units, smoothing, lock, Max/Min.IP67
This unit features a 0-7 bar operating range and a 10 bar over range. It is also IP67 rated.
|
Datasheet
|
|
User Manual
|
Hold, Zero, 7 selectable units, smoothing, lock, Max/Min.IP67
Featuring 0-10 bar operating range and a 21bar over range. This product is also IP67 rated.
|
Datasheet
|
|
User Manual
|
- 0-1 bar operating range
- 2 bar over range
- -10°C to 50°C
- Backlit function
- Zeroing function
- Hold function
- Range lock function
- Max/Min
- Selectable units of pressure
- Port size 4mm
| Datasheet |
| User Manual |
|
Datasheet
|
