DatasheetThe Isolation Amplifier DS 7200 is used for separation and conversion of bipolar and unipolar mV-signals such as those frequently used for current measuring with shunt-resistors or other applications.
- Easy selection of input and output range
Input and output range for unipolar and bipolar signals can be easily set by using DIP switch - Universal power supply for 20 to 253 V AC/DC
Applicable world-wide for all common supply voltages - 3-port isolation
Protection against erroneous measurements due to parasitic voltages or ground loops - Ultra small sized housing
12.5 mm housing with plug-in screw terminal blocks - High bandwidth; high accuracy
No distortion; no falsification of measured signal - Protective Separation, 5 kV Test Voltage
Protects service personnel and downstream devices against impermissibly high voltage - Maximum reliability
No maintenance costs - 5 Years Warranty
Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)
The Isolation Amplifier DS 7200 is used for separation and conversion of bipolar and unipolar mV-signals such as those frequently used for current measuring with shuntresistors or other applications.
Due to the easy selection of the input and output ranges, the new universal power supply and the ultra-small housing the Isolation Amplifier is suitable for flexible use. High reliability and Protective Separation are further characteristics that make the DS 7200 unrivaled.
The order key allows you to select the desired input and output ranges to which the unit will be adjusted at the factory before delivery. These can be easily reconfigured at any time by means of DIP switch settings. Subsequent readjustment or measured range compensation can then be performed at the zero/scan potentiometers on the front panel. Also the cut-off frequency can be adapted to the measurement task by using the DIP Switch.
The slim housing with 12.5 mm width saves space in your switch cabinet and facilitates by the practical plug-in screw terminal blocks the assembly. For range setting a simple housing unblocking is installed which makes it possible to reach easily all control elements on the DIN-rail.
The new universal power pack for 20 to 253 V AC/DC means the DS 7200 can be used anywhere in the world, with all mains power supplies. The unit’s high efficiency contributes significantly to reducing the unit’s own heat generation. This is reflected in extremely high reliability and long-term stability. A green LED on the front of the unit has been provided to monitor the power supply.
Input
| Input signals (terminal/switch selectable) |
± 60 mV, ± 100 mV, ± 150 mV, ± 250 mV, ± 300 mV, ± 500 mV 0 to 60 mV, 0 to 100 mV, 0 to 150 mV, 0 to 250 mV, 0 to 300 mV, 0 to 500 mV |
| Input resistance | > 100 kOhm |
| Input capacitance | Approx. 1 nF |
| Overload | ≤ 30 V |
Output
| Voltage | Current | |
| Output signals (switch selectable) |
± 10 V, 0 to 10 V, 2 to 10 V ± 5 V, 0 to 5 V, 1 to 5 V |
± 20 mA, 0 to 20 mA, 4 to 20 mA ± 10 mA, 0 to 10 mA, 2 to 10 mA |
| Load | ≤ 10 mA (1 kOhm at 10 V) | ≤ 12 V (600 Ohm at 20 mA) |
| Linear transmission range | unipolar: –2 to +110 %, bipolar: –110 to +110 % | |
| Residual ripple | < 20 mVrms | |
General data
| Transmission error | < 0.1 % full scale | |
| Temperature coefficient 1) | < 100 ppm/K | |
| Zero/Span compensation | ± 10 % | |
| Cut-off frequency -3 dB | 10 kHz, switchable to 30 Hz | |
| Response time T99 | 80 µs, 20 ms | |
| Test voltage | 4 kV AC, 50 Hz, 1 min., Input against output against power supply 5 kV AC, 50 Hz, 1 min., Input against output/power supply (DS7200HV only) |
|
| Working voltage 2) (Basic Insulation |
1000 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 | |
| Protection against electrical shock 2) | Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 600 V AC/DC for overvoltage category II and pollution degree 2 between all circuits. | |
| Ambient temperature | Operation Transport and storage |
–20 °C to +70 °C (-4 to +158 °F) –35 °C to +85 °C (-31 to +185 °F) |
| Power supply | 20 to 253 V AC/DC, | AC 48 to 62 Hz, approx. 2 VA DC approx. 1.0 W |
| EMC 3) | EN 61326-1 | |
| Construction | 12.5 mm (0.49″) housing, protection class: IP 20 mounting on 35 mm DIN rail acc. to EN 60715 |
|
| Weight | Approx. 100 g | |