DatasheettThe sensor signal will be compared with the set limit values. In case of overshooting or undershooting, the output relays react according to the set configuration.
Two relay outputs (synchronous switching) can be configured as MIN or MAX alarm in open-circuit or closedcircuit operation with the analog control electronics.
All setting elements are located behind the openable front cover and can also be operated when the unit is mounted. The switching points and the switching hysteresis can be
adjusted with potentiometers. The monitoring states are indicated by yellow LEDs.
The relay changeover contacts switch high power loads up to 6 A. Input, power supply and the outputs are safely galvanically isolated from each other.
The Protective Separation and the 24 V DC power supply make the DG 3602 and DG 3632 universally applicable for all measurement and industrial applications, as well as for building automation.
Product line
| Device | Order No. |
|---|---|
| Temperature Monitor for low impedance sensors | DG 3602 |
| Temperature Monitor for high impedance sensors | DG 3632 |
Technical Data
Input
| DG 3602 | DG 3632 | |
| Input ranges (switchable) | 0 … 300 Ω / 0 … 3 kΩ | 0 … 30 kΩ / 0 … 300 kΩ |
| Monitoring sensors | Pt100, Pt200, Pt500, Pt1000, Ni100, Ni120, Ni500, Ni1000, KTY and further RTD |
NTC Further high impedance RTD |
| Sensor current | ≤ 1.5 mA / 0.15 mA | ≤ 0.2 mA / 0.02 mA |
| Sensor connection | 2-wire sensor connection, manual compensation of line resistances required | |
| Switch point setting | 0 to 110 % with 12-turn potentiometer | |
| Hysteresis setting | 0 to 6 % or 0 to 60 % of measuring range switchable, adjustable with potentiometer | |
Output
| Contact type | 2 isolated changeover relays (SPDT), synchronous switching |
| Switching capability AC max. | 250 V / 6 A, 1500 VA |
| Switching capability DC max. | 250 V / 0.2 A, 115 V / 0.3 A, 30 V / 6 A |
| Recommended minimum load | 300 mW / 5 V / 5 mA |
| Status indication | yellow LED |
| Response time | < 50 ms |
General Data
| Switch error | < 0.2 % full scale | |
| Temperature coefficient 1) | < 150 ppm/K | |
| Test voltage | 4 kV AC, 50 Hz, 1 min. input against power supply against both switching outputs 3 kV AC, 50 Hz, 1 min. switching output 1 against switching output 2 |
|
| Working voltage (Basic Insulation) 2) |
1000 V AC/DC for overvoltage category II and 600 V AC/DC for overvoltage category III according to DIN EN 61010 with pollution degree 2 between input, power supply and both switching outputs. Furthermore 300 V AC/DC between output 1 and output 2. | |
| Protection against electrical shock 2) | Protective separation according to DIN EN 61140 by reinforced insulation according to DIN EN 61010 up to 600 V AC/DC at overvoltage category II and 300 V AC/DC at overvoltage category III at pollution degree 2 between input, power supply and both switching outputs. Furthermore 300 V AC/DC between output 1 and output 2. |
|
| Power supply | 24 V DC, 15 %, approx. 0.7 W | |
| Ambient temperature | Operation Transport and storage |
–20 °C to +60 °C (-4 to +140 °F) –35 °C to +85 °C (-31 to +185 °F) |
| EMC 3) | EN 61326 -1 | |
| MTBF (acc. to EN 61709 / SN 29500) | 297.1 years (Tamb. 40 °C, FIT 383.9) | |
| Construction | 12.5 mm (0.5″) housing, protection class IP 20, mounting on 35 mm DIN rail acc. to EN 60715 | |
| Connection | Captive plus-minus clamp screws, Wire cross-section max. 2.5 mm² / AWG 14 Stripped length 6 … 8 mm / 0.28 in, Screw terminal torque 0.8 Nm / 7 lbf in |
|
| Weight | 70 g | |
- Average TC related to full scale value in specified operating temperature range, reference temperature 23 °C
- For applications with high working voltages, ensure there is sufficient spacing or isolation from neighboring devices and protection against electric shocks
- Minor deviations possible during interference
Block diagram
Dimensions
Terminal assignments
- 1.1 +Power supply +
- 1.2 −Power supply −
- 3.1Input RTD
- 3.2Input RTD
- Output 1
- 4.1COM
- 4.2NO
- 5.1NC
- Output 2
- 6.1COM
- 6.2NO
- 5.2NC
Do not connect terminal 2.1 and 2.2
